Study(III) on the Development of Charts and Formulae Predicting Allowable Axial Bearing Capacity for Prebored PHC Pile Socketed into Weathered Rock through Sandy Soil Layer - The Proper Use of Long-term Allowable Compressive Load of PHC Piles by Analyzing Quality Test and Product Specifications Data -

Chae Min Kim; Dae Hee Yun; Chang Uk Lee; Yongkyu Choi

doi:10.7843/kgs.2019.35.9.15

All Issue

2019 Vol.35, Issue 9 Preview Page Next Page

Research Article

Study(III) on the Development of Charts and Formulae Predicting Allowable Axial Bearing Capacity for Prebored PHC Pile Socketed into Weathered Rock through Sandy Soil Layer - The Proper Use of Long-term Allowable Compressive Load of PHC Piles by Analyzing Quality Test and Product Specifications Data - 사질토층을 지나 풍화암에 소켓된 매입 PHC말뚝에서 지반의 허용압축지지력 산정도표 및 산정공식 개발에 관한 연구(III) - 품질 성능 검사 자료 및 성능 제원 표 분석을 통한 PHC말뚝의 장기허용압축하중 성능의 올바른 활용 -

30 September 2019. pp. 15-28

PDF XML

Abstract

PHC말뚝을 생산하는 17개 중소산업체의 품질 성능 검사 자료, 17개 중소산업체 및 6개 대기업 산업체의 장기허용압축하중 제원 표를 분석하였다. 현 단계의 국내 설계에서는 PHC말뚝의 장기허용압축하중의 평균 약 70% 수준을 반영하고 있고 품질이 우수함에도 불구하고 PHC말뚝의 장기허용압축하중에는 안전율 4.0을 적용하고 있다. 대부분의 품질 검사 기준은 KS F 4306에 명시되어 있다. 그러나 원심력으로 다져진 콘크리트 압축강도시험 기준은 KS F 2454에 명시되어 있다. 각 제조사의 품질 시험 자료를 분석한 결과 모든 항목에서 기준값 보다 높은 성능을 보였다. 따라서 PHC말뚝 설계 시 PHC말뚝의 지지력을 PHC말뚝의 허용연직압축하중의 최대값까지 사용할 수 있을 것으로 판단되었다.

Long-term allowable compressive Loads of PHC piles were analyzed based on qualification tests results by 17 small and medium PHC pile producing companies and product specifications by 6 major and 17 small and medium PHC pile producing companies. At the present stage, an average long-term allowable compressive load of PHC pile was designed at 70% level from current design data, and safety factor of 4.0 was applied to long-term allowable compressive loads of PHC pile despite of its excellent quality. Most quality standards of PHC pile are specified at KS F 4306. But compressive strength test method of spun concrete is specified at KS F 2454. As a result of analyzing quality test data supplied by each manufacturer, all quality test results showed higher performances than standard values. Therefore, it was considered that the capacity of PHC pile can be used up to the maximum allowable compressive load of PHC pile when PHC pile is designed.

Keywords

PHC pile

Quality standard of PHC pile

KS F 4306

Compressive strength test method of spun concrete

KS F 2454

Higher performances than standard values

Long-term allowable compressive load

References

Chae, S. G. (2018), Standard Design and Construction Practice for PHC Piles, GSENC Corp., p.14, p.173, p.174. (In Korean)

Cho, C. H. (2006), Bored pile method, ENG Book. (in Korean)

Choi, Y. K., Kwon, O. K., Lee, W. J., and Yeo, K. K., Park, M. C. (2019), A Study for Establishing of Behavior, Design and Construction on Prebored and Precast Piles (Development of Capacity Prediction Method and Chart for Prebored and precast Piles Considering Soil Types, Pile Penetration Lengths, Pile Diameter), Report No. KGS 2019-083, pp.21-45, 273-300. (In Korean)

Concrete Pile Construction Technical Association (2009), Foundation Structure Design Manual (Architecture), p. 8. (In Japanese)

FHWA (1983), Allowable stresses in piles, FHWA/RD-83/059, pp.41-44.

KATS (1983), KS F 4306 Pretensioned Spun High Strength Concrete Piles, 1983. 12. 17, pp.1-51. (In Korean)

Lee, I. M. (2014), Principles of Foundation Engineering, CIR, p. 121. (In Korean)

The Korea Land & Housing Corporation (2017), Appendix 1 Quality Test and Inspection Standards in Construction Specification, V1711, 2017. 8, p. Appendix 1-4. (In Korean)

Yea, G. G., Yun, D. H., Yun, D. K., and Choi, Y. K. (2019b), Study(II) on Development of Charts and formulae Predicting Allowable Axial Bearing Capacity for Prebored PHC Pile Socketed into Weathered Rock through Sandy Soil Layer - Improvement Measures of Current Design Method by Analyzing Current Design Data for Prebored PHC Piles -, JOURNAL OF THE KOREAN GEOTECHNICAL SOCIETY, Vol.35, No.8, August 2019, pp.31-42. (In Korean)

Yoo, N. J. etc. 20 Authors (2015), Design Specification and Commentary for Foundation Design, Korean Geotechnical Society, p.288. (In Korean)

OOPILE Ltd. (2018), Test frequency and test results for quality control. (In Korean)

Information

Publisher :The Korean Geotechnical Society
Publisher(Ko) :한국지반공학회
Journal Title :Journal of the Korean Geotechnical Society
Journal Title(Ko) :한국지반공학회 논문집
Volume : 35
No :9
Pages :15-28
Received Date : 2019-06-12
Revised Date : 2019-07-19
Accepted Date : 2019-07-20
DOI :https://doi.org/10.7843/kgs.2019.35.9.15

Journal of the Korean Geotechnical Society ISSN:1229-2427(Print) 2288-646X(Online) 한국지반공학회 논문집

All Issue